Tribology test standards

252 friction, wear, lubricant and component test standards. One request, the whole European testing network.

Showing all 252 standards

Lubricant and grease test standards

More on lubricant testing

  • ASTM D2266

    Four-ball wear test, lubricating grease

    See also: ASTM D4172, DIN 51350-3, DIN 51350-5Also in: Friction & wearTribometerPoint contact, rotating

  • ASTM D2509

    Timken OK load, lubricating grease

    Also in: Friction & wearTribometerLine contact

  • ASTM D2596

    Four-ball EP test, lubricating grease

    See also: ASTM D2783, ISO 20623, DIN 51350-2, DIN 51350-4Also in: Friction & wearTribometerPoint contact, rotating

  • ASTM D2670

    Pin and vee block wear, fluid lubricants

    Also in: Friction & wearTribometerLine contact

  • ASTM D2714

    Block-on-ring calibration and operation

    Also in: Friction & wearTribometerLine contact

  • ASTM D2782

    Timken EP test, lubricating fluids

    Also in: Friction & wearTribometerLine contact

  • ASTM D2783

    Four-ball EP test, lubricating fluids

    See also: ASTM D2596, ISO 20623, DIN 51350-2, DIN 51350-4Also in: Friction & wearTribometerPoint contact, rotating

  • ASTM D3233

    Pin and vee block EP, fluid lubricants

    Also in: Friction & wearTribometerLine contact

  • ASTM D3704

    Block-on-ring oscillating wear of greases

    Also in: Friction & wearTribometerReciprocating sliding

  • ASTM D4172

    Four-ball wear test, lubricating fluids

    See also: ASTM D2266, DIN 51350-3, DIN 51350-5Also in: Friction & wearTribometerPoint contact, rotating

  • ASTM D5183

    Four-ball coefficient of friction of lubricants

    Also in: Friction & wearTribometerPoint contact, rotating

  • ASTM D5706

    SRV EP test, lubricating greases

    See also: ASTM D6425, ISO 19291, ASTM D5707, ASTM D7421Also in: Friction & wearTribometerReciprocating sliding

  • ASTM D5707

    SRV friction and wear, lubricating greases

    See also: ASTM D6425, ISO 19291, ASTM D7421, ASTM D5706Also in: Friction & wearTribometerReciprocating sliding

  • ASTM D6425

    SRV friction and wear, EP oils

    ≡ DIN 51834-2See also: ISO 19291, ASTM D5707, ASTM D7421, ASTM D5706Also in: Friction & wearTribometerReciprocating sliding

  • ASTM D7420

    SRV grease in plastic ball joints

    Also in: Friction & wearTribometerReciprocating sliding

  • ASTM D7421

    SRV EP properties of oils

    See also: ASTM D6425, ISO 19291, ASTM D5707, ASTM D5706Also in: Friction & wearTribometerReciprocating sliding

  • ASTM D8227

    SRV synchronizer friction with transmission fluids

    Also in: Friction & wear · GearsTribometerReciprocating sliding

  • ASTM D8316

    SRV friction and wear of lubricating oils, cylinder on flat

    See also: DIN 51834-4Also in: Friction & wearTribometerReciprocating sliding

  • ASTM D8503

    SRV scuffing temperature limit of oils

    Also in: Friction & wearTribometerReciprocating sliding

  • DIN 51347-1

    Brugger test, general

    Also in: Friction & wearTribometerLine contact

  • DIN 51347-2

    Brugger lubricant test

    Also in: Friction & wearTribometerLine contact

  • DIN 51350-1

    Shell four-ball tester: general principles

    Also in: Friction & wearTribometerPoint contact, rotating

  • DIN 51350-2

    Four-ball welding load, fluid lubricants

    See also: ASTM D2783, ASTM D2596, ISO 20623, DIN 51350-4Also in: Friction & wearTribometerPoint contact, rotating

  • DIN 51350-3

    Four-ball wear, fluid lubricants

    See also: ASTM D4172, ASTM D2266, DIN 51350-5Also in: Friction & wearTribometerPoint contact, rotating

  • DIN 51350-4

    Four-ball welding load, greases

    See also: ASTM D2783, ASTM D2596, ISO 20623, DIN 51350-2Also in: Friction & wearTribometerPoint contact, rotating

  • DIN 51350-5

    Four-ball wear, greases

    See also: ASTM D4172, ASTM D2266, DIN 51350-3Also in: Friction & wearTribometerPoint contact, rotating

  • DIN 51350-6

    Shear stability of polymer oils, KRL bearing

    ≡ ISO 26422Also in: Friction & wearTribometerPoint contact, rotating

  • DIN 51834-1

    SRV oscillation apparatus: general principles

    Also in: Friction & wearTribometerReciprocating sliding

  • DIN 51834-4

    SRV friction and wear of lubricating oils, cylinder roller on flat

    See also: ASTM D8316Also in: Friction & wearTribometerReciprocating sliding

  • DIN 51834-5

    SRV friction-induced noise of brake fluids in EPDM-metal contact (SAE J1703/J1704, ISO 4925)

    See also: ISO 4925Also in: Friction & wearTribometerReciprocating sliding

  • EN 15427-2-1

    Twin-disc test, rail flange lubricant sticks

    Also in: Friction & wearTribometerLine contact

  • ISO 16047

    Thread friction, torque/clamp force of fasteners (screw pastes, assembly lubricants)

    Also in: Friction & wearTribometerConformal / flat-on-flat

  • ISO 19291

    SRV tribological properties of oils and greases (4 modes, incl. ASTM D6425, D7421, D5707, D5706)

    See also: ASTM D6425, ASTM D5707, ASTM D7421, ASTM D5706Also in: Friction & wearTribometerReciprocating sliding

  • ISO 20623

    Four-ball EP and wear, oils and greases

    See also: ASTM D2783, ASTM D2596, DIN 51350-2, DIN 51350-4, IP 239Also in: Friction & wearTribometerPoint contact, rotating

  • ASTM B117

    Salt spray (fog) testing

    Property / analysis

  • ASTM D1160

    Distillation at reduced pressure

    Property / analysis

  • ASTM D1264

    Water washout of greases

    See also: ISO 11009Property / analysis

  • ASTM D130

    Copper strip corrosion

    See also: ISO 2160, IP 154Property / analysis

  • ASTM D1401

    Water separability of oils

    See also: ISO 6614Property / analysis

  • ASTM D1403

    Cone penetration, quarter/half scale cone

    ≡ IP 310Property / analysis

  • ASTM D1404

    Harmful particles in grease

    Property / analysis

  • ASTM D1478

    Low-temperature torque, ball bearing grease

    Property / analysis

  • ASTM D1500

    ASTM colour

    ≡ IP 196See also: ISO 2049Property / analysis

  • ASTM D1743

    Corrosion-preventive properties of greases

    See also: ASTM D5969Property / analysis

  • ASTM D1748

    Humidity cabinet rust protection

    Property / analysis

  • ASTM D1831

    Roll stability of greases

    Property / analysis

  • ASTM D217

    Cone penetration of lubricating grease

    ≡ ISO 2137 · IP 50Property / analysis

  • ASTM D2265

    Dropping point, wide temperature range

    See also: ISO 2176Property / analysis

  • ASTM D2270

    Viscosity index calculation

    See also: ISO 2909, IP 226Property / analysis

  • ASTM D2272

    RPVOT rotating pressure vessel oxidation

    See also: IP 229Property / analysis

  • ASTM D2500

    Cloud point

    See also: ISO 3015Property / analysis

  • ASTM D2595

    Evaporation loss, wide temperature range

    Property / analysis

  • ASTM D2619

    Hydrolytic stability (beverage bottle)

    Property / analysis

  • ASTM D2893

    Oxidation of extreme-pressure oils

    Property / analysis

  • ASTM D2896

    Base number, perchloric acid

    ≡ ISO 3771 · IP 276Property / analysis

  • ASTM D2983

    Brookfield low-temperature viscosity

    See also: ASTM D8210Property / analysis

  • ASTM D3427

    Air release of oils

    ≡ IP 313See also: ISO 9120Property / analysis

  • ASTM D3829

    Borderline pumping temperature, engine oils

    Property / analysis

  • ASTM D4048

    Copper corrosion from grease

    Property / analysis

  • ASTM D4049

    Water spray-off resistance of greases

    Property / analysis

  • ASTM D4052

    Density, digital meter

    See also: ISO 12185, IP 365Property / analysis

  • ASTM D4310

    TOST sludge and corrosion, 1000 h

    Property / analysis

  • ASTM D445

    Kinematic viscosity

    See also: ISO 3104, IP 71Property / analysis

  • ASTM D4683

    HTHS viscosity, tapered bearing simulator, 150 C

    See also: ASTM D4741, ASTM D5481, ASTM D6616Property / analysis

  • ASTM D4684

    Mini-rotary viscometer (MRV), engine oils

    Property / analysis

  • ASTM D471

    Effect of liquids on rubber

    See also: ISO 1817Also in: SealsMaterial

  • ASTM D4739

    Base number, potentiometric (HCl)

    Property / analysis

  • ASTM D5133

    Scanning Brookfield, gelation index

    Property / analysis

  • ASTM D5185

    Elements in oils by ICP-AES

    Property / analysis

  • ASTM D5293

    Cold-cranking simulator (CCS)

    Property / analysis

  • ASTM D5481

    HTHS viscosity, multicell capillary

    See also: ASTM D4683, ASTM D4741, ASTM D6616Property / analysis

  • ASTM D5483

    Oxidation induction time of greases, PDSC

    Property / analysis

  • ASTM D5662

    Gear oil compatibility with seals

    Also in: Seals · GearsMaterial

  • ASTM D5800

    Noack evaporation loss

    See also: CEC L-40-93, DIN 51581-1Property / analysis

  • ASTM D5968

    Corrosion bench test, diesel engine oils, 121 C

    Property / analysis

  • ASTM D6082

    High-temperature foaming at 150 C

    Property / analysis

  • ASTM D6138

    EMCOR corrosion-preventive properties of greases

    See also: ISO 11007Property / analysis

  • ASTM D6184

    Oil separation, conical sieve

    Property / analysis

  • ASTM D6185

    Compatibility of binary grease mixtures

    Property / analysis

  • ASTM D6186

    Oxidation induction time of oils, PDSC

    Property / analysis

  • ASTM D6278

    Shear stability, Kurt Orbahn diesel injector, 30 cycles

    See also: CEC L-14-A-93Property / analysis

  • ASTM D6304

    Water by Karl Fischer

    See also: ISO 12937Property / analysis

  • ASTM D6335

    TEOST 33C deposits

    Property / analysis

  • ASTM D6417

    Engine oil volatility by gas chromatography

    Property / analysis

  • ASTM D6443

    Ca, Cl, Cu, Mg, P, S, Zn in unused oils and additives by WD-XRF

    Property / analysis

  • ASTM D6557

    Ball rust test, engine oils

    Property / analysis

  • ASTM D6594

    High-temperature corrosion bench test, 135 C

    Property / analysis

  • ASTM D6616

    HTHS viscosity, tapered bearing simulator, 100 C

    See also: ASTM D4683, ASTM D4741, ASTM D5481Property / analysis

  • ASTM D664

    Acid number, potentiometric

    ≡ IP 177See also: ISO 6619Property / analysis

  • ASTM D665

    Rust-preventing characteristics, inhibited oils with water

    ≡ ISO 7120 · IP 135Property / analysis

  • ASTM D6810

    Hindered phenol antioxidant (RULER)

    Property / analysis

  • ASTM D6922

    Homogeneity and miscibility of engine oils

    Property / analysis

  • ASTM D6971

    Antioxidants in turbine oils (RULER)

    Property / analysis

  • ASTM D7042

    Stabinger dynamic viscosity and density

    Property / analysis

  • ASTM D7097

    TEOST MHT deposits

    Property / analysis

  • ASTM D7109

    Shear stability, diesel injector, 30 and 90 cycles

    Property / analysis

  • ASTM D7279

    Kinematic viscosity, Houillon viscometer

    Property / analysis

  • ASTM D7414

    Oxidation in in-service oils by FTIR (trend analysis)

    Property / analysis

  • ASTM D7596

    Automatic particle counting and shape classification, direct imaging

    Property / analysis

  • ASTM D7624

    Nitration in in-service oils by FTIR (trend analysis)

    Property / analysis

  • ASTM D7647

    Automatic particle counting with dilution, light extinction

    Property / analysis

  • ASTM D7896

    Thermal conductivity of fluids

    Property / analysis

  • ASTM D8022

    Roll stability of greases with water

    Property / analysis

  • ASTM D8184

    Ferrous wear debris by particle quantifier (PQ index)

    Property / analysis

  • ASTM D874

    Sulfated ash

    See also: ISO 3987Property / analysis

  • ASTM D892

    Foaming characteristics of lubricating oils

    ≡ ISO 6247 · IP 146Property / analysis

  • ASTM D92

    Flash and fire point, Cleveland open cup

    See also: ISO 2592, IP 36Property / analysis

  • ASTM D93

    Flash point, Pensky-Martens closed cup

    See also: ISO 2719, IP 34Property / analysis

  • ASTM D942

    Oxidation stability of greases, oxygen bomb

    ≡ IP 142See also: DIN 51808Property / analysis

  • ASTM D943

    TOST oxidation, inhibited mineral oils

    See also: ISO 4263-1Property / analysis

  • ASTM D97

    Pour point

    See also: ISO 3016, ASTM D5950, ASTM D5949, ASTM D6892, ASTM D5985, ASTM D6749, ASTM D7346Property / analysis

  • ASTM D971

    Interfacial tension, oil against water

    Property / analysis

  • ASTM D972

    Evaporation loss of greases and oils

    See also: IP 183Property / analysis

  • ASTM D974

    Acid/base number, colour indicator

    ≡ IP 139See also: ISO 6618Property / analysis

  • ASTM E1131

    Compositional analysis by TGA

    Property / analysis

  • ASTM E2412

    Condition monitoring of in-service lubricants by FT-IR

    Property / analysis

  • DIN 51399-1

    Elements in lubricants by ICP-OES

    Property / analysis

  • DIN 51451

    Infrared spectrometry of lubricants

    Property / analysis

  • DIN 51452

    Oxidation of oils by infrared spectrometry

    Property / analysis

  • DIN 51453

    Oxidation and nitration of engine oils by IR

    Property / analysis

  • DIN 51558-2

    Neutralisation number, colour indicator titration

    Property / analysis

  • DIN 51777

    Water content by Karl Fischer titration

    See also: ASTM D6304, ISO 12937Property / analysis

  • DIN 51807-1

    Water resistance of greases (static)

    Property / analysis

  • DIN 51834-2

    SRV friction and wear, oils

    Property / analysis

  • IP 186

    Low-temperature torque of greases

    Property / analysis

  • IP 19

    Demulsification number (steam)

    Property / analysis

  • IP 266

    Grease churning test

    Property / analysis

  • IP 80

    Fraass breaking point (low-temperature brittleness)

    Property / analysis

  • ISO 12152

    Flender foam test

    Property / analysis

  • ISO 1817

    Rubber: effect of liquids

    See also: ASTM D471Also in: SealsMaterial

  • ISO 2176

    Dropping point of lubricating grease

    See also: ASTM D2265Property / analysis

  • ISO 3016

    Pour point of petroleum products

    See also: ASTM D97, ASTM D5950, ASTM D5949, ASTM D6892, ASTM D5985, ASTM D6749, ASTM D7346, IP 15Property / analysis

  • ISO 3733

    Water content by distillation

    Property / analysis

  • ISO 4406

    Particle contamination code of fluids

    Property / analysis

  • ISO 4925

    Brake fluid specification tests

    See also: DIN 51834-5Property / analysis

  • ISO 9408

    Aerobic biodegradability

    Property / analysis

  • OECD TG 301 B

    Ready biodegradability (CO2 evolution)

    Property / analysis

Coating test standards

More on coating testing

  • ASTM C1624

    Scratch adhesion of ceramic coatings

    Material

  • ASTM G171

    Scratch hardness with diamond stylus

    Also in: Materials & surfacesMaterial

  • EN 1071-13

    Pin-on-disk wear rate, ceramic coatings

    Tribometer

  • ISO 14577-1

    Instrumented indentation, test method

    Also in: Materials & surfacesMaterial

  • ISO 14577-4

    Instrumented indentation of coatings

    Also in: Materials & surfacesMaterial

  • ISO 20502

    Scratch adhesion of ceramic coatings

    Material

  • ISO 26424

    Micro-scale abrasion test

    Tribometer

  • ISO 26443

    Coating adhesion, Rockwell indentation

    Material

  • ISO 27307

    Transverse scratch test, thermal sprayed ceramic coatings

    Material

Gear test standards

More on gear testing

  • ASTM D4998

    FZG wear test, tractor hydraulic fluids

    Also in: LubricantsComponent

  • ASTM D5182

    FZG A/8.3/90 method, scuffing load stage

    Component

  • ASTM D5704

    L-60-1 test

    Component

  • ASTM D7038

    L-33-1 test

    Component

  • ASTM D7452

    L-42 axle test

    Component

  • ASTM D8165

    L-37-1 axle test

    Component

  • FVA 2/IV

    FZG pitting test

    Also in: LubricantsComponent

  • FVA 54/7

    FZG micropitting test

    Also in: LubricantsComponent

  • ISO 14635-1

    FZG A/8.3/90 scuffing load capacity

    See also: ASTM D5182Also in: LubricantsComponent

  • ISO 14635-2

    FZG step load test for high EP oils

    Also in: LubricantsComponent

  • ISO 14635-3

    FZG test for lubricating greases

    Also in: LubricantsComponent

Bearing test standards

More on bearing testing

  • ASTM D3336

    High-temperature life of greases in ball bearings

    Also in: LubricantsComponent

  • ASTM D3527

    Life performance of automotive wheel bearing grease

    Component

  • ASTM D3702

    Thrust washer wear of self-lubricated materials

    Also in: Friction & wear · LubricantsTribometerConformal / flat-on-flat

  • ASTM D4170

    Fafnir fretting wear protection by greases

    See also: ASTM D7594Also in: Lubricants · Friction & wearComponentFretting

  • ASTM D4290

    Leakage of wheel bearing grease, accelerated

    Component

  • ASTM D4693

    Low-temperature torque of grease-lubricated wheel bearings

    Component

  • DIN 51819

    FAG FE8 rolling bearing test

    Also in: LubricantsComponent

  • DIN 51821

    FAG FE9 grease life test

    Also in: LubricantsComponent

  • EN 12082-1

    Railway axleboxes: test procedures (rig test of bearings, housing, seals and grease)

    Component

  • IP 168

    Grease rolling-bearing performance

    Also in: LubricantsComponent

  • ISO 7148-1

    Testing of bearing metals

    Tribometer

  • ISO 7148-2

    Testing of polymer-based bearing materials

    Tribometer

Seal and elastomer test standards

More on seal testing

  • ASTM D1414

    Test methods for rubber O-rings

    Component

  • ASTM D4289

    Elastomer compatibility of greases and fluids

    Material

  • ASTM D6546

    Elastomer seals with industrial hydraulic fluids

    Material

  • ASTM D7216

    Engine oil compatibility with seal elastomers

    Material

  • CEC L-112

    Elastomer compatibility bench test

    Material

  • ISO 19880-7

    Rubber O-rings for hydrogen fuelling stations

    Material

  • ISO 23936-2

    Rapid gas decompression of elastomers

    Also in: HydrogenMaterial

  • ISO 34-1

    Tear strength of elastomers

    Material

  • ISO 4649

    Abrasion resistance of rubber (rotating drum)

    Component

  • ISO 48-2

    Rubber hardness, 10 to 100 IRHD

    Material

  • ISO 6072

    Hydraulic fluids and standard elastomers

    Material

  • NORSOK M-710

    Elastomer qualification incl. rapid gas decompression

    Also in: HydrogenMaterial

Hydrogen compatibility test standards

More on hydrogen tribology testing

  • ASTM E647

    Fatigue crack growth rates

    Material

  • ASTM F1624

    Hydrogen embrittlement threshold, incremental step loading

    Material

  • ASTM F519

    Hydrogen embrittlement of plating/coating processes

    Material

  • ASTM G142

    Embrittlement of metals in high-pressure hydrogen

    Material

  • ISO 11114-4

    Steels for hydrogen cylinders, embrittlement test methods

    Also in: Materials & surfacesMaterial

  • ISO 17081

    Hydrogen permeation in metals (electrochemical)

    Also in: Materials & surfacesMaterial

  • ISO 3690

    Diffusible hydrogen in arc weld metal

    Also in: Materials & surfacesMaterial

Bulk material and surface analysis standards

More on surface and materials analysis

  • AGMA 925-B22

    Effect of tribology and lubrication on gear surface distress

    Surface / material analysis

  • ASTM D7755

    Wear volume on SRV specimens by optical profilometry

    Also in: Friction & wear · CoatingsSurface / material analysis

  • ASTM E3

    Preparation of metallographic specimens

    Surface / material analysis

  • ASTM E407

    Microetching of metals and alloys

    Surface / material analysis

  • DIN 50905-4

    Corrosion testing in waters

    Surface / material analysis

  • ISO 21920-2

    Profile surface texture: terms and parameters

    ≡ ISO 21920Also in: Friction & wear · CoatingsSurface / material analysis

  • ISO 21920-3

    Profile surface texture: specification operators

    Also in: Friction & wear · CoatingsSurface / material analysis

  • ISO 25178-2

    Areal surface texture: terms and parameters

    ≡ ISO 25178Also in: Friction & wear · CoatingsSurface / material analysis

  • ISO 25178-3

    Areal surface texture: specification operators

    Also in: Friction & wear · CoatingsSurface / material analysis

  • ISO 25178-602

    Areal surface texture: confocal chromatic probe

    Also in: Friction & wear · CoatingsSurface / material analysis

  • ISO 25178-604

    Areal surface texture: coherence scanning interferometry

    Also in: Friction & wear · CoatingsSurface / material analysis

  • ISO 25178-606

    Areal surface texture: focus variation

    Also in: Friction & wear · CoatingsSurface / material analysis

  • ISO 25178-607

    Areal surface texture: confocal microscopy

    Also in: Friction & wear · CoatingsSurface / material analysis

  • ISO 643

    Grain size of steels (micrographic)

    Also in: Friction & wear · CoatingsSurface / material analysis

  • ISO 6507-1

    Vickers hardness

    Also in: CoatingsSurface / material analysis

  • ISO 6508-1

    Rockwell hardness

    Also in: CoatingsSurface / material analysis

  • ISO 945-1

    Graphite microstructure of cast irons

    Also in: Friction & wear · CoatingsSurface / material analysis

  • VDI 3822

    Failure analysis: fundamentals and performance

    Surface / material analysis

  • VDI 3822 Blatt 1.3

    Failures caused by tribological loading

    Surface / material analysis

Friction, wear, abrasion and erosion test standards

More on friction and wear testing

  • ANSI A326.3

    Dynamic coefficient of friction of hard flooring (BOT-3000E)

    Tribometer

  • ASTM B611

    Abrasive wear of cemented carbides

    Also in: Coatings · Materials & surfacesTribometerAbrasion and erosion

  • ASTM D2625

    Pin and vee endurance of solid film lubricants

    Also in: CoatingsTribometerLine contact

  • ASTM D2981

    Block-on-ring wear life of solid films, oscillating

    Also in: CoatingsTribometerReciprocating sliding

  • ASTM D7217

    SRV EP properties of solid bonded films

    Also in: CoatingsTribometerReciprocating sliding

  • ASTM D7594

    SRV fretting wear, greases at high Hertz pressure

    See also: ASTM D4170Also in: Lubricants · BearingsTribometerFretting

  • ASTM F732

    Pin-on-flat wear of polymers for joint prostheses

    Also in: Materials & surfacesTribometerReciprocating sliding

  • ASTM G105

    Wet sand / rubber wheel abrasion

    Also in: Coatings · Materials & surfacesTribometerAbrasion and erosion

  • ASTM G119

    Synergism of wear and corrosion

    Also in: Coatings · Materials & surfacesTribometerTribocorrosion

  • ASTM G132

    Pin abrasion testing

    Also in: Coatings · Materials & surfacesTribometerAbrasion and erosion

  • ASTM G133

    Linearly reciprocating ball-on-flat sliding wear

    See also: EN 1071-12Also in: Coatings · Materials & surfacesTribometerReciprocating sliding

  • ASTM G137

    Block-on-ring sliding wear of plastics

    Also in: Materials & surfacesTribometerLine contact

  • ASTM G176

    Block-on-ring wear of plastics, cumulative

    Also in: Materials & surfacesTribometerLine contact

  • ASTM G181

    Piston ring vs cylinder liner friction, lubricated

    Also in: Other componentsTribometerReciprocating sliding

  • ASTM G196

    Galling resistance, rotating method

    Also in: Coatings · Materials & surfacesTribometerConformal / flat-on-flat

  • ASTM G204

    Fretting wear, damage in sliding contacts

    Also in: Coatings · Materials & surfacesTribometerFretting

  • ASTM G223

    Twist compression friction and adhesive wear

    Also in: Coatings · Materials & surfacesTribometerConformal / flat-on-flat

  • ASTM G32

    Vibratory cavitation erosion

    Also in: Coatings · Materials & surfacesTribometerAbrasion and erosion

  • ASTM G65

    Dry sand / rubber wheel abrasion

    Also in: Coatings · Materials & surfacesTribometerAbrasion and erosion

  • ASTM G73

    Liquid impingement erosion

    Tribometer

  • ASTM G75

    Slurry abrasivity (Miller number, SAR)

    Also in: Materials & surfacesTribometerAbrasion and erosion

  • ASTM G76

    Solid particle erosion, gas jet

    Tribometer

  • ASTM G77

    Block-on-ring sliding wear ranking

    Also in: Coatings · Materials & surfacesTribometerLine contact

  • ASTM G98

    Galling resistance of materials

    Also in: Coatings · Materials & surfacesTribometerConformal / flat-on-flat

  • ASTM G99

    Pin-on-disk wear testing

    See also: ISO 20808Also in: Coatings · Materials & surfacesTribometerPin/ball-on-disc, rotating sliding

  • DIN 51834-3

    SRV tribological behaviour of materials/coatings

    Also in: CoatingsTribometerReciprocating sliding

  • EN 1071-12

    Reciprocating wear test, ceramic coatings

    See also: ASTM G133Also in: CoatingsTribometerReciprocating sliding

  • EN 16165

    Slip resistance of pedestrian surfaces

    Tribometer

  • ISO 20808

    Friction and wear of fine ceramics, ball-on-disc

    See also: ASTM G99Also in: Coatings · Materials & surfacesTribometerPin/ball-on-disc, rotating sliding

  • VDA 230-206

    Stick-slip of material pairs

    Tribometer

Other component test standards: engines, pumps, brakes, clutches

More on component testing

  • ASTM D5966

    Roller follower wear, light-duty diesel engine

    Component

  • ASTM D6891

    Sequence IVA

    Component

  • ASTM D6973

    High-pressure vane pump test

    Component

  • ASTM D7043

    Vane pump wear, hydraulic fluids (constant volume)

    Also in: LubricantsComponent

  • ASTM D7422

    Mack T-12

    Component

  • ASTM D7484

    Cummins ISB

    Component

  • ASTM D7549

    Caterpillar C13

    Component

  • ASTM D8111

    Sequence IIIH

    Component

  • ASTM D8226

    Sequence VIF

    Component

  • ASTM D8256

    Sequence VH

    Component

  • ASTM D8279

    Sequence X

    Component

  • ASTM G206

    Guide: wear volume of piston ring segments

    Component

  • ISO 20763

    Vane pump anti-wear, hydraulic fluids

    Also in: LubricantsComponent

  • JASO T903

    Four-stroke motorcycle oil specification

    Component

  • SAE J2522

    Brake pad performance, AK Master dynamometer

    Component
No match yet. Send us the standard anyway: we also adapt standards and design custom tests.

Need one of these tests?

Send the standard number and your samples. We choose the right laboratory, manage the test and deliver one report.

Request a test

Standard tests, run where they run best

i-TRIBOMAT, the European Tribology Centre, gives you one entry point to more than 130 test rigs across Europe. This list covers the ASTM, ISO, DIN, EN, IP, CEC, FVA and other standards most requested in tribology and lubricant testing: four-ball and SRV tests, grease and oil properties, FZG gear tests, FE8 and FE9 bearing tests, pin-on-disc and reciprocating wear, abrasion and erosion, coatings, seals and hydrogen compatibility.

The same test often exists under several numbers: ASTM, ISO, IP, DIN, EN or CEC. Where the standards themselves state that methods are technically equivalent, we show them together on one card (≡). Similar methods that differ in conditions or results, such as the four-ball or SRV variants, stay separate and point to each other, so you request exactly the method your specification requires.

Many customers need more than a standard test. We adapt standards to real operating conditions (temperature, atmosphere, load, materials), combine tests from tribometer to component scale, and store your results in your own online database.

0 tests selected